1700 Series Cylinder Series magnetostrictive absolute displacement sensor built German original product image Product Overview 1700 Series Cylinder Series magnetostrictive absolute displacement sensor built specifically for the hydraulic cylinder built-in installation is designed to provide high accuracy (0.01% FS), direct and absolute The position detection feedback. The series of high frequency response, fast refresh (2000Hz), anti-jamming, small hysteresis (0.5ms), high precision, suitable for high speed real-time monitoring and control of hydraulic motion (10m / s) of the system, but also adapt to the complex interference environments (anti-frequency interference) . Non-contact characteristics to avoid mechanical wear to ensure that the theoretically infinite life. Fastening flange and measuring rod made of high quality stainless steel, it can be directly inserted into the high-pressure hydraulic cylinder, and will not appear corrosion. Design uses a sub-structure, the vault can be easily removed from the flange and replace, to avoid leakage and cylinder relief, protecting the environment, but also to facilitate quick repairs. Protection class IP65 can for complex and harsh environment sensors provide adequate protection. DIN43650 universal plug connectors, widely used in equipment hydraulic equipment, it is very easy field wiring installation. Plug connectors have several characteristics: ① universal plug connector built-in special double throw switch allows customers to choose the logical direction of the signal, such as: 0 ~ 10V output will be switched to 10 ~ 0V output, or vice versa; ② special V / A plug linker can be converted into a voltage output signal current output signal, and the built-in double-throw switch selection signal direction, such as: the 4 ~ 20mA converted into 20 ~ 4mA. Current signal transmission distance up to 500 meters. ③ Output current can be adjusted at both ends of the reference position. ④ no customers in the internal wiring, avoiding possible mistakes. Tighten the mounting flange ring installation diagram Legend: mounting thread M20 × 2 read by the M18 × 1.5 overall installation diagram showing the basic parameters DrawingWiring type linear displacement measuring input voltage 24Vdc (20.4 ~ 28.8Vdc) Input protection polarity protection : reverse voltage to 30Vdc, 36Vdc positive voltage to a maximum current consumption of 50 ~ 140mA (depending on the working stroke varies) Dielectric strength 500Vdc (between the power supply with the device ground) Output 0 ~ 10Vdc and 10 ~ 0Vdc two output, minimum 5KΩ 4 ~ 20mA load resistance and 20 ~ 4mA two output, maximum load resistance 700Ω Resolution Infinite resolution (depending on the controller A / D and power supply ripple) Repeatability <± 0.005% FS Linearity <± 0.01% FS (Minimum ± 90μm) refresh rate 1200mm stroke of 0.5ms / 2400 mm stroke is 1.0ms 4800mm stroke 2.ms / 7600mm stroke of 5.0ms Operating Temperature -40 ~ + 85 ℃ Protection class IP65 vibration test 5g / 10 ~ 2000Hz comply with IEC standard 68-2-6 Impact test 50g single blow, in line with IEC standard 68-2-27 pressure rating 350bar / 600bar peak mounting screw M20 x 2 bulk material vault anodized aluminum / measuring rod and mounting flange 316 stainless steel Installation joints requirements Figure Purchase Guidelines 1700-XXXXmm-YZ Description 1700 on behalf of a cylinder built-Series magnetostrictive displacement sensor XXXX represents the effective stroke: 0075mm representatives 75mm; 0250mm representatives 125mm; 1250mm behalf of 1250mm. Y represents the output signal: V represents an output 0 ~ 10Vdc and 10 ~ 0Vdc two output; A representative of the output 4 ~ 20mA and 20 ~ 4mA two output. Z represents a sensing device: 1-ring installation mode; 2 float installation mode product composition and packing slips V Output Product: V-type output of the sensor body, magnetic (or magnetic ring), V-type plug, Products and description; A Output Product: V-type output of the sensor body, magnetic (or magnetic ring), V / A type plug, product introduction and description; vault vault with flange replacement guidelines for the split, when you need fast When replacing the sensor, the vault can be easily removed and replaced from the flange. You can achieve rapid maintenance site to avoid leakage of the hydraulic system relief and cause environmental pollution.